Compatible sensors		Strain gauge transducer
Signal input terminals		Round connector(NDIS7P)/terminal bank(connect only one at a time)
Bridge Voltage		DC, 2.5 V ±5% (30mA maximum current)
Signal input range		±5 mV/V
D/A output		± 2V
Equivalent input/TEDS	Calibration range	0.3 mV/V – 5.0 mV/V
Equivalent input/TEDS	Calibration precision	Within 0.1% F.S. (when using a 1m standard TEAC Φ8, 6-core shielded cable with 350Ω impedance, when 5mV/V)
Precision	Linearity	Within 0.01% F.S. + 1 digit (when 5mV/V)
	Zero drift	Within 0.5 μV/°C (input conversion value)
	Gain drift	0.005%/ºC or less
A/D conversion		1000 times/second, 24-bit
Digital filter		Moving average (select from OFF, 16, 32, 64, 128, 256, 512, 1024, 2048)
D/A output	Output connector	BNC
	Output voltage	±2.0 V
	Resolution	70.16μV typ
	Linearity	0.02% F.S. or less
	Zero drift	0.1 mV/ºC or less
	Gain drift	0.003%/ºC or less
TEDS function		IEEE1451.4 class 2 mix mode interface
Display	Display	2.4" color TFT LCD
	Display modes	Setting screens, indicator value digital display, graph display, recorded data list display, static strain display
	Languages	Japanese/English
Indicator value	Display range	－99999 to 99999
Indicator value	Decimal point	Display position selectable
Displayed items	Calibration settings	Zero calibration/span calibration (TEDS calibration, actual load calibration, equivalent input calibration)
	Function settings	High limit, low limit, comparison mode, hysteresis, nearly zero, moving average, motion detect, zero tracking, digital zero, digital zero offset, zone definition, hold mode, control lock, minimum grid, digital zero limit, clear digital zero, select data output, D/A converter
	Sensor value memory	Six types of calibration values for each connected sensor
Hold functions		Sample hold, peak hold, bottom hold, zone definition hold (peak, bottom)
Data recording	Indicator value	300 maximum Recorded contents: ID number, date and time, recording mode, sensor value memory number, indicator value
Data recording	Graph recording	8 maximum Recorded contents: ID number, date and time, sensor value memory number, trigger mode, graph waveform
Power supply		4 alkaline or NiMH AA batteries USB bus power (built-in Micro-USB B connector)
Operating temperature range		0℃ to 40℃
Storage temperature range		－20℃ to 60℃
Operating humidity range		85% RH or less (without condensation)
Applicable standards		CE marking, VCCI (Class A), FCC (Class A), UKCA
External dimensions (W×H×D)		Approximately 85mm × 140mm × 35mm (without protrusions)
Weight		About 320 g (including batteries)

TD-01掌上型荷重元指示計

TD-01 Portable

High-performance color graphic LCD screen

2.4" color TFT LCD provides great visibility and a variety of information display.

It can be displayed in the color behavior judgment.

Waveform & bar meter display function

Graphical chart allows users to check input signals instinctively.

TEDS function (Automatic calibration)

TEDS function reads the calibration information to automatically, and records calibration values when the power is turned on.

Sensor information can be displayed and rewritten.

Indicator value list

This function can display a list of recorded indicator values.

Waveform screen can be recorded, displayed and compared.

Static Strain Disp. Mode

Show the input signal with the strain amount unit.

This function makes it easier to check load-cells for plastic deformation.

Interrupt Check

Disconnecting becomes readily apparent at a field.

If the possibility of an interruption is detected, the location of the possible interruption will be shown in red.

Dual Input

Round connector (NDIS7P)

Connecting with the terminal bank

Dual language Support (English and Japanese)

Japanese / English changeable.

Multiple power supply system

Continuous operation time on four AA batteries power is approximately 24 hours (when the EVOLTA alkaline batteries are used).

USB bus power can enable the unit to drive for many hours continuously.